Arcsite Multiunit

Roof Framing Terminology: Components, Rafters & Definitions

Author

Christian Collison

Christian Collison

Director of Business Development & Partnerships

Roof Framing Terminology: Components, Rafters & Definitions

Roof framing can seem complicated mainly because it has its own vocabulary. Terms such as run, rise, ridge board, jack rafter, birdsmouth and shortening allowance often appear together, and understanding one usually makes the next easier to follow.

This guide explains the terminology used throughout conventional roof framing and roof trusses. It is based on the supplied roof-framing reference and is written as a practical glossary for homeowners, buyers, renovators and anyone trying to make sense of roof-space observations or a building inspection report.

Rather than treating the terms as isolated definitions, the guide groups them by how they are used. We begin with roof geometry, then move through the main framing members, rafter cuts and layout terms, roof forms, framing-square terminology and roof truss components.

Why Roof Framing Terminology Matters

Roof framing terms describe three things: the shape of the roof, the measurements used to set it out and the structural members that create that shape. If one of those changes, the terminology used to describe the framing often changes as well.

A simple gable roof, for example, is framed mainly with common rafters running from the wall plates to the ridge. A hip roof adds diagonal hip rafters and shorter jack rafters. Where two roof sections meet internally, a valley is created and valley rafters are introduced. The vocabulary follows the geometry of the roof.

Understanding these terms is useful when reading plans, discussing alterations or interpreting inspection findings. It does not replace project-specific structural design or an assessment of whether a roof is adequate for its loads and supports.

Roof Geometry Terms: Span, Run, Rise and Pitch

Before looking at individual timber members, it helps to understand the measurements used to describe a roof. The supplied reference introduces span, run, rise and line length early because these measurements establish the geometry that rafter layout depends on.

Span

Span is the horizontal distance across the building or between the principal supporting points of the roof. In a simple symmetrical gable roof, it extends from one outside wall line to the other.

Run

Run is the horizontal distance used to lay out one side of a roof. On a straightforward symmetrical gable roof, the run is generally half the span because the ridge sits near the centre of the building.

The reference also uses total run to describe the full horizontal distance relevant to a framing calculation or roof section.

Rise

Rise is the vertical height gained as the roof travels horizontally. It works with run to establish the slope. Total rise refers to the overall vertical change between the lower and upper reference points.

Unit Rise and Unit Run

Unit rise and unit run express the same slope relationship in smaller, repeatable measurements. Instead of working only with the total dimensions of the roof, the framer can use a consistent amount of rise for a set unit of horizontal run and transfer that relationship along the rafter.

Roof Pitch and Slope

Pitch and slope describe how steeply the roof rises. A steeper roof gains more vertical height over the same horizontal distance, while a lower-pitched roof gains less.

Line Length

Line length is the sloping distance along a rafter between its reference points. Because it travels diagonally, it is longer than the horizontal run.

In basic roof geometry, rise and run form the shorter sides of a right triangle, while the rafter line forms the sloping side. This relationship is used repeatedly when determining rafter lengths.

Main Roof Framing Components

Once the roof geometry is understood, the next group of terms describes the members that create the roof. The reference distinguishes between common, hip, valley and jack rafters while showing how they relate to the ridge and wall framing.

Ridge Board

The ridge board runs along the high line of a conventionally framed roof. Opposing common rafters meet at the ridge, helping establish their alignment and the roof centreline.

Wall Plate

The wall plate is the horizontal member at the top of the wall framing that provides a lower bearing point for the rafters. Rafter layout normally includes a seat or birdsmouth so the member can bear on the plate while maintaining the required slope.

Common Rafter

A common rafter is one of the regular sloping members that forms the main plane of a roof. It typically runs from the wall plate towards the ridge.

The source uses the common rafter as the starting point for many framing calculations. Once its run, rise, length and cuts are understood, the geometry of more complex members becomes easier to follow.

Hip Rafter

A hip rafter runs diagonally from an outside corner towards the ridge. It appears on hip roofs, where the roof slopes down on more than two sides.

Because it travels diagonally across the roof plan while also rising, its geometry differs from a common rafter. Jack rafters terminate against the hip instead of continuing to the ridge.

Valley Rafter

A valley rafter follows an internal diagonal line where two roof sections intersect. It supports the framing that runs into the valley between the roof planes.

Intersecting roofs may have equal or unequal spans. When the roof sections differ, the location of the ridges, valleys and adjoining rafters changes accordingly.

Jack Rafter

A jack rafter is a shortened rafter used where a full-length common rafter cannot continue between the usual wall and ridge lines.

The reference identifies several types. Hip jack rafters run between the wall plate and a hip rafter. Valley jack rafters frame into a valley. Cripple or hip-valley jack rafters are short members used between diagonal framing members in more complex intersections.

Although their lengths change according to position, jack rafters still follow the roof plane and the broader rafter spacing.

Collar Tie

A collar tie is a horizontal member installed between opposing rafters higher in the roof. The reference discusses collar ties as part of conventional roof assembly and shows how their ends follow the rafter slope.

Rafter Layout and Cut Terminology

Roof framing terminology also describes the marks and cuts made on each rafter. These terms explain how a straight piece of timber is shaped so it can meet the ridge, bear on a wall and form an eave.

Plumb Cut

A plumb cut is a vertical cut relative to the building when the rafter is installed. At the upper end of a common rafter, it allows the member to meet the ridge board. The roof slope determines the angle of the cut.

Seat Cut

The seat cut is the horizontal bearing portion of the notch where a rafter sits on the wall plate. It provides a bearing surface and works with the adjoining vertical cut to locate the rafter at the wall line.

Birdsmouth

Birdsmouth is the common name for the notched section of a rafter that fits over the wall plate. In the source, the birdsmouth includes the seat cut and the plumb line at the wall.

It is more than a simple notch: it establishes the bearing point while allowing the rafter to continue at the intended roof slope.

Rafter Tail, Projection and Overhang

The rafter tail is the portion that continues past the wall after the bearing point. This projecting length helps create the roof overhang or eave.

Projection therefore affects the final rafter length. A rafter may have a calculated length between structural reference points and additional length beyond the wall.

Shortening Allowance

Shortening allowance is an adjustment made to a theoretical rafter length so the member fits correctly against another framing component.

A common rafter, for example, is shortened to account for the thickness of the ridge board rather than extending to an imaginary centreline. Similar allowances occur in hip and valley framing.

Side Cut

A side cut appears on diagonal members such as hip and valley rafters where the end must fit another component at an angle in plan as well as in elevation.

The reference treats this separately from standard plumb and seat cuts because diagonal rafters meet the ridge differently from common rafters.

Backing and Dropping a Hip Rafter

The source uses backing and dropping when explaining how a hip rafter may be adjusted so the roof surfaces align correctly. Backing alters the upper edges of the hip, while dropping lowers it relative to the theoretical framing line.

These are more advanced layout terms, but they show why a hip rafter cannot always be treated exactly like a longer common rafter.

Roof Form Terminology

Many framing terms make more sense once the roof form is clear. The source begins with four main pitched-roof forms because each introduces a different combination of rafters and intersections.

Gable Roof

A gable roof has two sloping surfaces that meet at a ridge. Common rafters rise from opposing wall plates towards that ridge, making the gable a useful starting point for understanding basic rafter layout.

Hip Roof

A hip roof slopes on all sides. Hip rafters form the outside diagonal lines, common rafters form the main roof planes and jack rafters shorten progressively as they approach the hips.

Intersecting Roof

An intersecting roof occurs where one roof section joins another. The internal junction forms a valley, and the layout can differ depending on whether the roof sections have equal or unequal spans.

Shed or Lean-To Roof

A shed or lean-to roof has a single main slope. Its rafters generally run from a higher support to a lower support rather than meeting at a central ridge.

Dormer

A dormer projects from or interrupts a larger roof plane. It introduces additional framing because the main rafter pattern may need to be shortened or rearranged around the opening. The source discusses dormers both with and without sidewalls.

Framing Square Terminology

The framing square receives a substantial section in the source because traditional rafter layout depends on transferring roof geometry to the timber. Its terminology is still useful when reading older framing instructions.

Blade, Tongue and Heel

A framing square has two legs that meet at a right angle. The longer, wider leg is the blade; the shorter, narrower leg is the tongue; and the point where they meet is the heel.

These parts are used when rise and run values are set on the square before a rafter is marked.

Stepping Off

Stepping off is a method of repeatedly moving the framing square along a rafter to transfer the unit rise and unit run relationship.

Each step represents another unit of horizontal run, allowing the overall rafter line to be laid out from a repeated geometric relationship.

Rafter Table and Scales

Traditional framing squares may carry tables and graduated scales. The supplied reference discusses rafter tables, brace information and board-measure scales.

For roof framing, the important point is that these markings help convert known roof geometry into usable lengths and layout references.

Roof Truss Terminology

The final part of the source moves from individually framed rafters to roof trusses. The vocabulary changes because a truss combines several members into a complete structural unit.

Top Chord and Bottom Chord

The top chords are the sloping outer members that follow the roof profile. The bottom chord spans between the lower supports and forms the base of the truss.

Web Members

Web members are the internal members connecting the top and bottom chords. Their arrangement varies between truss types and helps transfer forces through the unit.

Gusset

A gusset is a connecting piece used at a truss joint. The source shows both plywood and metal gusset arrangements used to connect members so that the individual pieces work together as one unit.

Common Truss Types

The reference illustrates several truss forms. A king-post truss uses a central vertical member. A W-type or Fink truss uses internal webs arranged in a W-like pattern. A scissor truss uses sloping lower chords rather than a flat horizontal bottom chord.

The shapes differ, but each is made up of connected members designed to transfer loads to the supports.

Tension and Compression

The source explains that truss members can be subjected mainly to tension or compression. Tension means a member is being pulled, while compression means it is being pushed.

Understanding these terms helps explain why the truss relies on the complete arrangement of chords, webs and connections rather than on any one member acting alone.

Temporary and Permanent Bracing

Bracing keeps trusses aligned and stable. Temporary bracing is used while the trusses are being erected, while permanent bracing remains as part of the completed roof system.

How the Terms Work Together

Roof framing terminology is easier to remember when the terms are connected instead of memorised individually.

Consider a simple gable roof. The span establishes the overall width between supports. Half of that span may establish the run. Rise and run define the slope and the theoretical line length of a common rafter. The rafter receives a plumb cut at the ridge and a birdsmouth at the wall plate, while the tail continues beyond the wall to form the overhang.

Change the same roof to a hip roof and new terms appear. Hip rafters run diagonally from the outside corners, jack rafters shorten towards the hips, and shortening and side-cut considerations become part of the layout. Join another roof to it and valleys, valley rafters and more complex jack rafters can be introduced.

Each term therefore describes a measurement, framing member, cut, connection or roof form that relates directly to the rest of the system.

Roof Framing Terms in Building Inspections

For homeowners and buyers, knowing the terminology can make a building inspection report easier to interpret. If an inspector refers to the roof space, rafters, ridge or visible framing alterations, understanding the basic members provides useful context.

Residential Reports’ building reports may include observations on accessible roofing, roof-space areas, eaves and fascia as part of the broader inspection. A condition inspection is different from structural design: visible concerns can be documented, while questions about engineering adequacy, concealed framing or the design of alterations may require further specialist assessment.

Where the concern is whether building work corresponds with approvals or property documentation, a compliance report addresses a different question from a condition-based inspection.

For current Australian structural requirements, the National Construction Code and the applicable referenced standards should be checked for the individual building. Standards Australia identifies AS 1684.2 as a key residential timber-framing standard for non-cyclonic areas.

Quick Reference: Common Roof Framing Definitions

The following recap is intended as a quick reference after the main explanations above. Seeing the terms in context first makes the shorter definitions much easier to use.

  • Span — horizontal distance across the principal roof supports.
  • Run — horizontal distance used to lay out one side of a roof.
  • Rise — vertical height gained over the run.
  • Line length — sloping distance along the rafter.
  • Ridge board — member along the high line where opposing common rafters meet.
  • Common rafter — regular rafter running from the wall plate towards the ridge.
  • Hip rafter — diagonal rafter at an outside roof corner.
  • Valley rafter — diagonal rafter at an internal roof intersection.
  • Jack rafter — shortened rafter used around hips and valleys.
  • Birdsmouth — notch that allows a rafter to bear on the wall plate.
  • Plumb cut — cut aligned vertically when the rafter is installed.
  • Seat cut — horizontal bearing surface within the birdsmouth.
  • Rafter tail — section extending beyond the wall line.
  • Shortening allowance — adjustment from theoretical length to account for the actual framing connection.
  • Top chord — sloping outer member of a roof truss.
  • Bottom chord — lower member spanning between truss supports.
  • Web member — internal truss member connecting the chords.
  • Gusset — plate or piece used to connect truss members.

Understanding Roof Framing as a Complete System

Roof framing terminology is more than a collection of trade expressions. The terms describe how the roof is measured, how its members are positioned and how those members meet.

Span, run and rise establish the geometry. Common rafters create the basic roof planes. Hip and valley rafters define diagonal intersections. Jack rafters fill the spaces around them. Plumb, seat and birdsmouth cuts allow members to fit the ridge and walls. Trusses use a different vocabulary of chords, webs and gussets, but the same overall purpose remains: creating a connected structural system that carries the roof across the building.

For homeowners, buyers and renovators, understanding these definitions can make plans, roof-space observations and inspection reports easier to follow. Where a roof shows signs of alteration, deterioration or unusual framing, however, terminology is only the starting point. A professional assessment is needed to determine what the condition means for the individual property.

Christian Collison

Director of Business Development & Partnerships

A results-driven Director of Business Development & Partnerships with a strong track record of building strategic alliances, driving revenue growth, and unlocking new market opportunities. Specializes in identifying high-impact collaborations and scaling partnerships that deliver long-term value.